Family run in Pleasant Hill, Oregon since 1976

Monday to Friday, 8am to 4pm rainbowpump@yahoo.com (541) 726-1394
Manual hand pump well casing electrical box ferns pleasant hill lane county

Hand Pump Services

Backup Hand Pump for the Well in Eugene, OR

A hand pump for the well in Eugene, OR, keeps water flowing when the power or the electric pump fails. Rainbow Pump Co Inc installs and services hand pumps, including Simple Pump. Call (541) 726-1394.

Signs Your Home Needs a Backup Hand Pump for Well Water

An electric well pump stops the moment the power goes out, and a rural home on a private well loses its water along with its lights. A backup hand pump for well water gives you a way to draw water without electricity, whether the outage lasts an hour or several days. For many rural households, a hand pump for the well in Eugene, OR, and the surrounding valley is the simplest way to keep drinking water within reach.

Some properties need a backup more than others. A hand pump is worth considering if any of these sound familiar:

  • Storms or winter weather knock out your power from time to time
  • You keep livestock or animals that need water every day
  • Your property is a cabin or outbuilding without reliable power
  • You want water on hand if the electric pump fails
  • An older hand pump on the property no longer draws water
  • You are planning for emergencies and want water that needs no fuel
Blue gloved hand filling beaker white kitchen faucet water sample eugene

Simple Pump Installation

Simple Pump is a manual deep well hand pump made in the United States, built in Nevada since 1999. The manufacturer rates it to lift water from static water levels as deep as 325 feet, which puts it within reach of many wells that an old pitcher pump could never draw from.

In many wells, a Simple Pump shares the casing with the existing electric submersible pump. Each pump works on its own, so you keep the convenience of the electric pump every day and gain a manual one for outages. The manufacturer notes that a 4 inch casing can be tight, while 5 and 6 inch casings leave more room for both.

A Simple Pump can also push water into your home's pressure tank, so a few minutes at the handle can supply the house plumbing rather than only a bucket at the wellhead. Simple Pump installation from Rainbow Pump starts with measuring your well to confirm the fit.

Water holding tank pressure tank pump system pleasant hill

Well Hand Pump Installation Alongside Your Submersible

Well hand pump installation in a working well takes careful planning, because two pumps, two sets of pipe and the electric pump's wire all have to fit in the same casing without rubbing or tangling. Our technicians measure the casing diameter, the well depth and the static water level before choosing a layout.

The wellhead changes as well. A hand pump needs a well cap that allows both pumps through, and the water it pumps has to reach the house, either through the top of the well or through a pitless adapter below ground. When the existing pitless fitting is worn, our pitless adapter installation service replaces it in the same visit.

Once the hand pump is in place, we test it by hand and confirm the electric pump still runs as it should. The goal is two independent ways to get water from one well.

Bolted black well cap blue casing poly pipe elbow grass lowell oregon

Manual Well Pump Options for Shallow and Deep Wells

A manual well pump comes in two broad types. A shallow well suction pump, often called a pitcher pump, pulls water up by suction, which limits it to water levels within roughly 25 feet of the surface.

Many household wells hold their water deeper than that, and there a deep well lift pump is the only choice that works. A lift pump places its cylinder down in the water and pushes water up with each stroke of the handle, which is how a deep well hand pump such as Simple Pump reaches far below the suction limit.

The right choice depends on your static water level, your casing size and how you plan to use the water. Our technicians measure the well first, then recommend the type of hand pump that will actually work in it.

Threaded metal pipe end water stream close up pleasant hill well pump

How a Hand Pump Installation Comes Together

A hand pump is only useful if it works on the day you need it. That is why every install starts with measurements and ends with a real test at the handle, not just a pump set in the well.

  • 1

    Measure the Well

    We record casing size, well depth and static water level to confirm which hand pump will fit and reach the water.

  • 2

    Plan the Layout

    We decide how the hand pump shares the casing with any electric pump and where its water will go.

  • 3

    Install the Pump

    We set the cylinder, pipe and rods in the well, fit the well cap and connect the outlet or pitless fitting.

  • 4

    Test at the Handle

    We pump by hand until water flows steadily and confirm the electric pump still runs normally.

Hand Pump Repair and Service

Hand pumps have few moving parts, but those parts wear. Seals and check valves inside the cylinder can wear over time, letting water drain back down the pipe so the pump needs many strokes before water appears. Handles, rods and fittings can loosen or corrode.

Our technicians inspect the pump from the handle down, replace worn parts where they can be replaced, and tell you plainly when an old pump is better retired. An old pump that was never matched to the water level in its well is usually better replaced than rebuilt.

A backup pump also deserves a test now and then. Working the handle a few times a year confirms it is ready before the next storm. If it takes more strokes than it used to before water appears, call us to check the seals and valves.

Gloved hand water sample test tube forested mountain lake pleasant hill

What Affects the Cost of a Hand Pump Installation

The cost of a hand pump for the well in Eugene, OR, depends first on how deep the water sits. A deeper static water level needs more pipe and rod, and sometimes a larger cylinder, to lift water to the surface.

Your existing setup matters too. Installing a hand pump alongside a working submersible takes more planning and labor than setting one in an empty well. Whether the water runs to a spigot at the wellhead or to your pressure tank, and whether the pitless adapter or well cap needs replacing, also shapes the price.

Our technicians measure the well and explain each option before work begins. You know what the install involves and why before any pipe goes in the well.

Excavated pit black well seal blue pipe pitless adapter lane county

Why Rainbow Pump

Why Choose Rainbow Pump for a Hand Pump for the Well in Eugene, OR

Rainbow Pump Co Inc has worked on well pumps since 1976. The Jones family acquired the company and carries on a family tradition of hands-on management, with pump installation and repair at the center of the business.

Our technicians have decades of experience and factory training from top pump manufacturers. They know how a hand pump and an electric submersible behave in the same casing, which is the hard part of a dual-pump install.

We work on residential, commercial and agricultural pumps, and we are licensed with the Oregon Construction Contractors Board, CCB #38493. A hand pump is one of our water well pump services across Lane County, alongside submersible well pump service and installation.

Yellow submersible pump beside open green well cover lane county oregon

Hand Pump Installs Near Eugene, Springfield and Pleasant Hill

Our shop sits in Pleasant Hill, and we serve rural properties within about 50 miles. Homes outside city water lines depend on their wells for every glass of water, and when the power goes out, their water goes with it.

We install hand pumps for homeowners needing well pump service in Eugene, on the rural edges of Springfield and around Pleasant Hill. We also reach the smaller communities across our Lane County service areas.

A hand pump for the well in Eugene, OR, or anywhere nearby, is a one-time project that pays off every time the power goes out. Our technicians bring the same careful measuring and testing to every property, whatever its size.

Hand Pump Questions

Can a hand pump be installed in the same well as my electric pump?

In many cases, yes. A deep well hand pump such as Simple Pump can share the casing with an existing submersible pump, and each works on its own. The fit depends on the casing diameter, the size of the electric pump and the well depth, so our technicians measure the well before recommending a dual-pump install.

How deep can a hand pump draw water?

A shallow well suction pump is limited to water within roughly 25 feet of the surface. A deep well lift pump works much deeper, and Simple Pump rates its deep well hand pump for static water levels up to 325 feet. The static water level in your well, not the total depth, decides which pump will work.

Can a hand pump supply water to my whole house?

A hand pump can deliver water to a spigot at the wellhead, and some models, including Simple Pump, can pump into your home's pressure tank. Filling the tank by hand lets you run faucets and flush toilets during an outage. Our technicians can tell you which setup suits your well and your plumbing.

Does a hand pump need any power or fuel?

A manual hand pump needs no electricity, fuel or batteries. You lift water by working the handle, which is what makes it a dependable backup during long outages. The trade is effort and flow: a hand pump delivers far less water per minute than an electric pump, so it suits essential use rather than daily household demand.

Weathered teal cast iron hand pump spout rust close up lane county
Water pouring into clear drinking glass blue background lane county well water

Water Without Power

Get Water From Your Well When the Power Is Out

The next outage is a poor time to wish you had a backup. Call Rainbow Pump Co Inc to talk about a hand pump for your well, and our technicians will measure it and recommend a pump that will work when you need it most.