Family run in Pleasant Hill, Oregon since 1976

Monday to Friday, 8am to 4pm rainbowpump@yahoo.com (541) 726-1394
Sunlit pressure switch gauge brass tee fittings blue tank pitless lane county

Repair and Maintenance

Well Pressure Tank Repair in Eugene, OR, and Lane County

Rainbow Pump Co Inc provides well pressure tank repair in Eugene, OR, and nearby towns, restoring steady pressure to existing tanks. Call (541) 726-1394, Monday to Friday, 8am to 4pm.

Signs of a Waterlogged Pressure Tank

A waterlogged pressure tank has lost the air cushion that pushes water out to your faucets. With little or no air left, the tank fills with water almost at once, and the pump has to start for nearly every glass you pour. The fault is common, and it usually shows up in a few recognizable ways.

  • The pump clicking on and off every few seconds while water runs
  • Pressure that jumps and falls instead of staying steady
  • Water coming out of the air valve when its core is pressed
  • A tank that feels heavy and sounds solid all the way to the top
  • Lights that flicker each time the pump starts

Catching it early protects more than the tank. Constant starts wear the pump motor, the capacitor and the pressure switch contacts, so a quick repair now can spare a larger well pump repair later.

Blue jet pump motor mounted on tank gauge pressure switch cottage grove or

Restoring the Pressure Tank Air Charge

Every pressure tank depends on its pressure tank air charge, the cushion of air that sits above the water or behind the bladder. In a bladder tank, that charge should sit a couple of psi below the pressure switch's cut-in setting. Over time, a small amount of air escapes through the valve or the bladder wall, and the tank slowly loses its ability to deliver water between pump starts.

To restore it, we shut off the pump, drain the tank completely and check the charge with a gauge at the air valve. We then bring it back to the right level and look for anything that would let it drop again, such as a leaking valve core.

A tank that loses its charge again within weeks usually has a torn bladder or a pinhole leak. At that point, recharging only delays the problem, and we will tell you so plainly.

Blue ball valve pressure switch gauge flexible hose cinder block wall lane count

Pressure Tank Cycling On and Off and Other Common Faults

Pressure tank cycling on and off is the symptom we are called about most, but the tank is not always the cause. A pressure switch with burned contacts, a clogged switch tube, a check valve that leaks back into the well or a dripping fixture can all make a pump short cycle. We test each part instead of guessing, which is the heart of good well pressure tank repair in Eugene, OR, and everywhere else we work.

Other repairs we handle on existing tanks include leaking tank tees, failed gauges, corroded fittings, stuck relief valves and air volume controls on older galvanized tanks. Many of these are small parts, though they decide whether the whole system holds pressure. A slow drip at a fitting can drain the tank between uses and make the pump start for no reason.

Technician hairnet pointing pressure gauge pressure relief valve stainless tank

How We Work

Our Tank Repair Process, From Diagnosis to Retest

A good repair starts with finding the real cause. We work through the system in the same order on every call, so nothing is overlooked and you know what was done.

  • 1

    Diagnose the Symptom

    We watch the pump cycle, read the gauge through a full run and check the pressure switch, so we know whether the fault is in the tank or elsewhere.

  • 2

    Drain and Inspect

    We shut off power, drain the tank and test the air charge, then inspect the bladder, the valve, the tank tee and the fittings for leaks or rust.

  • 3

    Recharge or Repair

    We restore the air charge, replace worn parts and reset the switch, or we explain why the tank needs replacing and what the options are.

  • 4

    Retest the System

    We restore power, run the pump through several full cycles and confirm steady pressure at the gauge and the faucets before we close out the visit.

Routine Pressure Tank Maintenance That Prevents Breakdowns

Most tank failures give warning, and regular pressure tank maintenance catches them early. A yearly look at the air charge, the gauge and the fittings takes little time and keeps the pump from working harder than it should.

During a maintenance visit, we check the precharge against the switch setting, look for rust on the shell and the base, test the relief valve where one is fitted, and confirm that the pump runs and rests as it should. We also note anything that is starting to wear, so you can plan a replacement instead of facing one on a weekend.

Tanks in unheated spaces deserve extra attention in winter. Eugene averages 52 nights a year at or below freezing, and a cracked fitting or gauge often traces back to one cold night in a well house.

Pressure switch gauge manifold blue pressure tank concrete pad pleasant hill

What Affects the Cost of Tank Repair

We give a price after we have diagnosed the system, because the same symptom can come from very different faults. A recharge with no parts is the simplest visit, while a leaking tank tee, a new switch or several corroded fittings add parts and time. Wiring or a check valve problem found during diagnosis adds its own work, and we explain it before going further.

Access matters too. A tank in a crawl space or a tight well house takes longer to drain and work on than one in an open garage. When a tank has a failed bladder or a rusted shell, repair stops making sense, and we will walk you through pressure tank installation for a properly sized replacement instead.

Water holding tank pressure tank pump system pleasant hill

Why Rainbow Pump

Why Choose Rainbow Pump for Well Pressure Tank Repair in Eugene, OR

Rainbow Pump Co Inc has served private well owners since 1976, and the Jones family continues its tradition of hands-on management. Our technicians have decades of experience and factory training from top pump manufacturers, so well pressure tank repair in Eugene, OR, is handled by people who know the whole water system.

  • Founded in 1976 and based in Pleasant Hill
  • Licensed with the Oregon Construction Contractors Board, CCB #38493
  • Residential, commercial and agricultural systems
  • Pumps, switches and tanks diagnosed together

We repair the tank you have whenever a repair is sound. When it is not, we say so, explain why and help you weigh the cost of another repair against a properly sized new tank.

Buried well pit tank excavation pleasant hill oregon

Tank Repair Around Pleasant Hill, Springfield and Eugene

From our shop in Pleasant Hill, we repair pressure tanks for homes and properties within about 50 miles, including well pump service in Eugene, well pump service in Springfield and well pump service in Pleasant Hill. Rural properties throughout our Lane County service areas depend on a working tank every time someone opens a tap.

Tank repair is one part of the water well pump services we provide for private wells in the southern Willamette Valley. A visit for a tank fault is also a good time to have the pump, the switch and the wiring looked over. Homeowners from the valley floor to the foothills call us for well pressure tank repair in Eugene, OR, and the surrounding communities.

Pressure Tank Repair Questions

Can a waterlogged tank be fixed, or does it need replacing?

It depends on why it waterlogged. A bladder tank that slowly lost air through its valve can usually be drained and recharged. A tank whose bladder has torn will waterlog again soon, because water now sits on both sides of the membrane. We test which case you have and recommend a recharge only when it will actually last.

Why does water come out of the air valve on my tank?

Water at the air valve almost always means the bladder inside the tank has ruptured. Air and water are mixing in the space that should hold only air. Recharging will not hold for long once this happens. In most cases, the tank needs to be replaced, and we check the pump and switch at the same time for damage from short cycling.

How often should the air charge on a pressure tank be checked?

Checking the air charge once a year is a sensible habit for most homes on a well. The check takes a gauge and a fully drained tank, so it pairs well with a routine system visit. If the charge has dropped noticeably since the last check, that is an early sign of a slow leak at the valve or in the bladder.

Is it the tank or the pressure switch that makes my pump short cycle?

Either can, and so can a leaking check valve or a dripping fixture. A tank with low air makes the pump start and stop on a short, regular rhythm while water runs. A switch with a clogged tube or worn contacts tends to chatter or behave erratically. We test both before replacing anything, so you only pay for the part that failed.

What should I do if my tank is leaking onto the floor?

Turn off the power to the pump at its breaker so it does not keep running against the leak, then close the valve between the tank and the house if you have one. Wipe the area dry so we can see where the water comes from. Call us during business hours, and we will find whether the leak is a fitting or the tank itself.

Black holding tank cream pressure tank green pump new home construction springfi
Yellow submersible pump beside open green well cover lane county oregon

Get It Fixed

Schedule Your Tank Repair With Rainbow Pump

A tank that holds its charge keeps your pressure steady and saves the pump from thousands of needless starts. Call (541) 726-1394, Monday to Friday, 8am to 4pm, or send us a message and we will set up a time to diagnose the problem.